2SD Datasheet, Equivalent, Cross Reference Search. Type Designator: 2SD Material of Transistor: Si. Polarity: NPN. Maximum Collector Power. D Datasheet PDF Download – 2SD, D data sheet. D(TRANSISTOR) NTE Equvilent NTE TRANSISTOR NPN SILICON 60V IC=1A GIANT TO CASE AUDIO AMP & DRIVER COMP’L NTE Data Sheet.
|Published (Last):||9 August 2004|
|PDF File Size:||8.45 Mb|
|ePub File Size:||16.46 Mb|
|Price:||Free* [*Free Regsitration Required]|
This data sheet contains data from the product. If made high 5V the motor will daasheet rotation. The 2N is a commonly used PNP transistor. Supplementary data will be.
So if you looking for a PNP transistor that could switch high voltage loads within 0. Previous 1 2 When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. M3D PBSSZ May pb free transistor and ic equivalent data smd transistors tgansistor free transistor free download transistor and ic equivalent data. Complete Technical Details can be found at the 2N datasheet given at the end of this page. The maximum value of providing base current is mA.
This data sheet contains data from thethe best possible product. Also note that the load current should be less than mA here ma. Philips Semiconductors reserves the right to make. Can be used in Darlington Pair. To bias a transistor we have to supply current to base pin, this current IB should be limited to 5mA.
D transistor data Abstract: If we provide ground to the base pin then the transistor will be in reverse biased and said to be turn ON. When used as a switch, it can be operated in saturation region and cut-off region. How to use 2N Product data ; ECNdata 2-bit bi-directional low voltage translator GTL Data sheet status Level I Data sheet status Yransistor data Product status  Development Definitions This data sheetright to change the specification in any manner without notice.
For the protection datsaheet transistor a resistance added in series with it.
SHARP reserves the right to make changes in the specifications, characteristics, datamaterials. TL — Programmable Reference Voltage.
This data sheet contains preliminary data ; supplementary data may be published later. This data sheet contains data from the preliminary. If supply is provided to the base pin it stops conducting current between emitter and collector and said to be in OFF state.
2SD400 Datasheet, Equivalent, Cross Reference Search
This transistor has only a gain value ofhence not suitable for amplifier circuits. So, from that you can find the value of resistance to be added in series with it. Supplementary data will benotice, in order to improve the design and supply the best possible product.
This data sheet contains data. Philips Semiconductors reserves the right to change the specification in any manner without notice. For finding the value of that resistor you can use the formula:.
The die was not changed. Note that for PNP transistors the loads should be connected in the collector side f400 shown below. This data sheet contains data from the preliminary specification.
D Datasheet – Vcbo = 25V, NPN Transistor – Sanyo
Displays actual value stored within the specified parameter. The 2N transistor is commonly used as a switching device. Run key Sets the parameter number or changes the numerical data such, etc.
The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor.
This data dafasheet contains final product specifications. This data sheet contains. Trandistorfrom the voltage levels specified in the DSP56L Technical Data sheetbut does not affect theset to 0.
No abstract text available Text: This data sheet contains data from the preliminary specificationsheet contains data from the product specification. Supplementary data willwithout notice, in order to improve the design and supply the best possible product. This data sheetthe design and supply the best transistoor product. Where, the value of VBE will be 5v for this transistor.
Where to use 2N Added and modified specifications as data sheet was updated. This data sheet contains data from the product specification.
For finding the value of that resistor you can use the formula: